三分PK拾

当前位置:三分PK拾-三分PK拾 > 三分PK拾

白铁皮人工的加工要求标准您清楚吗?

发布人:http://www.xoombulbs.com   发布时间:2017-10-26 17:03:28

1.使用白铁加工压口机时不要用力推动铁皮。压横接号应先将咬口部分铲掉。手离压轮要大于20毫米。

1. the use of tin processing pressure machine don't push iron. The horizontal connection number should be first removed from the bite part. Hand off pressure roller is greater than 20 mm.

三分PK拾使用咬口机要将白铁皮的咬口处对好后再开车。开车时工件要扶稳,手指不得放在咬口机轨道上。

Use the bite holder to bite the iron sheet properly and then drive it again。 When driving, the workpiece should be stable, and the finger should not be placed on the rail of the bite machine。

2.滚床的齿轮必须加防护套罩。使用时应离开两压辊的缝隙,并宜在进料处加安全挡板。

2。 gear hobbing machine must be combined with a protective cover。 When using, the gap between the two rollers should be left, and the safety baffle should be added at the feeding place。

使用白铁加工剪板机,上刀架不得放置工具等物品。调整铁皮时脚不能放在踏板上。剪切时禁止把手伸入压板空隙中。

The use of tin processing shears, tools and other items shall not be placed on the knife。 The feet should not be placed on the pedals when adjusting the iron sheet。 When cutting, don't put the handle into the gap of the press plate。

3。进行锡焊时要戴手套,不许仰焊。熔锡时锡液不许着水,防止飞溅。使用的电烙铁及盐酸要妥善保管。

To wear gloves 3. soldering, no overhead welding. Tin bath is not allowed to splash water and prevent spatter. Proper use of electric iron and hydrochloric acid should be kept in good order.

QQ截图20170428145456.png

4.操作电钻和半自动螺丝刀时,要垂直于白铁加工的铁皮,旦不要用力过猛。使用点焊机要检查有无漏电漏水现象,操作时要戴焊工手套、鞋盖、墨镜等防护用品,冬季使用后要放尽冷却液。

4. the operation of electric drill and semi-automatic screwdriver, perpendicular to the processing of tin tin, Dan do not overexert. Use spot welding machine to check whether there is leakage or leakage, and wear protective gloves such as welder gloves, shoes cover, sunglasses and so on. The cooling liquid should be put out after use in winter.

5.在保温层外包白铁皮时,要扎好衣袖、裤脚、袖口,戴好口罩、防尘帽和防护眼镜。

5. in the insulation layer outsourcing tin, to tie the sleeves, trousers, cuffs, wearing masks, protective glasses and dust cap.

6.吊运风管及材料时,索具要拴牢,并应加溜绳稳住。用麻绳滑车吊运时拉绳人要戴安全帽。

6. lifting air pipes and materials, rigging should be fastened ropes, and should be added. With a rope pulley hanging rope to wear a helmet.

三分PK拾7.不要在未固定的风管、架空的铁皮上站立和行走。

7。 do not stand and walk on the unfixed air pipe and the aerial iron sheet。

8。废弃的边角余料要及时清理,防止刺伤手脚。

8. waste leftover materials should be cleaned in time to prevent stab wounds.


上一篇:顺发黑白铁加工技术越来越强
下一篇:工厂房在通风管道的使用上有什么特点?

网站三分PK拾 关于我们 产品展示 三分PK拾 工程案例 在线留言 联系我们

山东11选5开奖 利来彩票注册 山西快乐十分 飞速飞艇 北京赛车代理抽水多少 天津11选5 河北11选5和值分布 天津11选5 重庆幸运农场网址 飞速时时彩